Canon 3410 Guía de usuario

User's GuideUser's GuideLaser Beam Printer

9 Heavy PaperThis printer can print heavy paper that is 76.2 to 215.9 mm wide, 127.0 to 355.6 mm long, and that weighs between 90 and 199 g/m2, inclu

10•Be sure to load them in portrait orientation with the printing side facing up.(: Feeding direction)•Printing speed drops when printing postcards, r

11•Before loading the envelopes, flatten the stack of envelopes to release any remaining air, and press the fold lines along the edges tight.•Do not pr

12 Plain Paper/Heavy Paper/Transparency/LabelYou cannot print on any area within 5 mm of the edges of paper. Postcard/Reply Postcard/4 on 1 Postcard

13You may have to change the printable area before printing, depending on the application you use.* 7.6 mm for the right edge of an envelope at a size

14-Paper that has already been printed by a copy machine or another laser printer (The reverse side of the paper is also unusable. Using the multi-pur

15Paper Capacity of the Output Trays* Actual paper capacity varies depending on the installation environment, paper type and paper size.Paper TypeOutp

16Loading Paper in the Paper CassetteLoad paper in the paper cassette. The paper loading methods are different between standard size paper and custom

171Pull out the paper cassette.CAUTIONBe sure to take the paper cassette out of the printer before loading paper. If paper is loaded while the paper c

18● While holding the lock release lever of the rear paper guide, slide the guide to the size mark for the paper to be loaded.Align the position of (A

1 Contents Turning the Printer ON/OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Tur ning the Printer ON . .

19•To print letterhead paper or paper printed with a logo, load the paper so that the printing side is facing down, as shown in the following figures.

204Hold down the paper as shown in the figure, make sure that the paper stack does not exceed the load limit marks (A), and then set it under the hooks

21IMPORTANTThe following shows the paper capacity of the paper cassette. Be sure that the paper stack does not exceed the load limit marks. If the pap

22 -When the paper is loaded in portrait orientation: <ユーザセッテイサイズ R > • When you change the orientation of the loaded custom size paper frequen

23 2 Load the paper so that the edge of the paper is aligned with the front side of the paper cassette.CAUTION When loading paper, take care not to c

24NOTE • To print letterhead paper or paper printed with a logo when loading paper in portrait orientation, load the paper so that the printing side

25 • To print letterhead paper or paper printed with a logo when loading paper in landscape orientation, load the paper so that the printing side is

26IMPORTANT Be sure to align the paper guides with the width of the paper. If the paper guides are too loose or too tight, this may result in misfeed

27 5 Hold down the paper as shown in the figure, make sure that the paper stack does not exceed the load limit marks (A), and then set it under the ho

28IMPORTANT The following shows the paper capacity of the paper cassette. Be sure that the paper stack does not exceed the load limit marks. If the p

2 Turning the Printer ON/OFF The printer can be turned ON/OFF using the power switch on the right side of the printer body. Be sure to observe the fo

29 Loading Paper in the Multi-purpose Tray Load paper in the multi-purpose tray. The paper loading procedure varies depending on the paper type. Refe

30 2 Pull out the auxiliary tray.IMPORTANT Be sure to pull out the auxiliary tray when loading paper in the multi-purpose tray. 3 When loading long-s

31 4 Spread the paper guides a little wider than the actual paper width. 5 Before loading transparencies or labels, fan them in small batches and ali

32 6 Gently load the stack of paper with the printing side facing up until it touches the back of the tray. Be sure that the paper stack is loaded un

33NOTE To print letterhead paper or paper printed with a logo, load the paper in the proper orientation according to the following instructions:- Wh

34 -When loading custom size paper in landscape orientation, load the paper so that the printing side is facing up as shown in the following figures.(

35IMPORTANT Be sure to align the paper guides with the width of the paper. If the paper guides are too loose or too tight, this may result in misfeed

36 2 Pull out the auxiliary tray.IMPORTANT Be sure to pull out the auxiliary tray when loading paper in the multi-purpose tray. 3 When loading long-s

37 4 Spread the paper guides a little wider than the actual paper width. 5 Before loading envelopes, align them as shown in the following figures. ● P

38 ● Loosen any stiff corners of the envelopes and flatten curls as shown in the figure. ● Align the edges of the envelopes on a flat surface. 6 Gently

3 If no abnormality is found during the self-diagnostic test, the オンライン indicator, 印刷可 indicator and Paper Source indicator for the currently selec

39CAUTION When loading paper, take care not to cut your hands with the edges of the paper.IMPORTANT • Load postcards or envelopes as shown in the fol

40 • You can load up to approximately 50 sheets of postcards at sizes of Postcard, Reply postcard, 4 on 1 postcard, and 4 on 1 postcard recommended b

41 Paper Jams When a paper jam occurs during printing for some reason, the printer beeps, displaying the message <13 ヨウシガ ツマリマシタ > in the displ

42 • The error message may remain if jammed paper is removed without opening the front cover. In this case, open and close the front cover once. • Do

43 • The surroundings of the output tray and sub-output tray are hot during printing or immediately after printing. When taking out of the paper or r

44 Paper Jam Area The messages displayed in the display indicate where the paper is jammed. Paper Jam AreaDisplay Message a Duplex print transport ar

45 Procedure for Clearing Paper Jams Remove any jammed paper using the following procedures. 1 Confirm all the messages that appear in the display. Me

46 3 Close the multi-purpose tray.bca

47 4 Open the front cover. Open the front cover gently while pressing the lever on the top surface of the cover. 5 Remove the toner cartridge from th

48 6 Place the toner cartridge into the protective bag. 7 Raise the transport guide, then tilt it toward you. Holding the green tab, raise the transp

4 1 Make sure that the ジジジジョョョョブブブブ indicator is off. 2 Press " " of the power switch on the printer.Off

49 8 Remove any jammed paper by pulling it in the direction of the arrow. Remove the jammed paper gently to prevent unfixed toner from spilling.IMPORT

5010Check the output tray and remove any jammed paper.IMPORTANTIf the jammed paper cannot be removed easily, do not try to remove it forcefully but pr

5112Turn the green dial in the sub-output tray in the direction of the arrow to send any jammed paper.When you have been performing automatic 2-sided

5214Close the front cover.Close the front cover completely until it clicks.15Pull out the paper cassette.

53If the paper feeder is installed, pull out the paper cassette of the paper feeder also.16Push any jammed paper downward slowly and forcefully to rem

54In case of the paper feederIf you have not been performing automatic 2-sided printing, proceed to Step 20.IMPORTANTBe sure not to touch the feed rol

5517Open the duplex print transport guide.Press the green lock release switch (A) as shown in the figure.18Remove any jammed paper by pulling it in the

5619Close the duplex print transport guide.Close both sides of the duplex print transport guide firmly.IMPORTANTMake sure that the duplex print transpo

57If the paper feeder is installed, set the paper cassette of the paper feeder also.21Open the front cover.Open the front cover gently while pressing

5822Take the toner cartridge out of the protective bag.23Push the toner cartridge into the printer until it touches the back of the printer while alig

5 Online and Offline When the printer can receive data from the computer and print the data, the printer is in the state of "Online", and wh

5924Close the front cover.Close the front cover completely until it clicks.

60Replacing the Toner CartridgeThis section describes how to replace or handle the toner cartridges and precautions on storing them.When <トトトトナナナナー

61IMPORTANT If the printing appears faint or inconsistent even when the message <16  トナー ヨウイ > or <16 トナー カクニン > does not appear, this ma

62 1 Open the front cover. Open the front cover gently while pressing the lever on the top surface of the cover. 2 Remove the toner cartridge from th

63IMPORTANT Do not touch the high-voltage contacts (A) or the electrical contact (B) shown in the figure, as this may result in damage to the printer.

64 ● Using a slightly dampened cloth with water, wipe off chipped paper and toner that are attached to the transport guide. After wiping off the dirt

65 ● Move the transport guide back to its original position slowly.CAUTION Do not take your hands off the transport guide until it moves back to its

66 5 Hold the toner cartridge as shown in the figure, and shake it gently 5 or 6 times to evenly distribute the toner inside the cartridge.IMPORTANT •

67CAUTION If the sealing tape is pulled out forcefully or stopped at midpoint, toner may spill out. If the toner gets into your eyes or mouth, wash t

68 7 Hold the toner cartridge properly with the arrowed side facing up as shown in the figure.IMPORTANT Do not hold the toner cartridge in a manner th

6NOTE If the printer has entered the sleep mode 1, the オンライン indicator is off even when the printer is online, and only the 印刷可 indicator and 主電源

69 8 Push the toner cartridge into the printer until it touches the back of the printer while aligning (A) on both sides of the toner cartridge with

70Canceling a JobIf you want to cancel the job currently being printed, perform "Cancel Job" using the following procedure. A job cancel all

71 Confirming the Printer Features This printer is provided with a function of Status Print that allows you to check the menu settings, etc. Use these

72 4 Confirm the contents of the Status Print. Status Print prints information as shown in the following figure. Status Print allows you to confirm info

73 Service Call Display When a problem has occurred and the printer does not work properly, the service call shown in the figure appears: 1 Turn the p

74 2 Note down the alphanumeric characters and message in the display. 3 Turn the printer and computer OFF a , remove the USB cable b , disconnect

75 Message List When the printer cannot continue printing for some reason (an error status), the printer beeps, the メッセージ indicator comes on, and an

7612 カバーガ アイテイマス Cause The front cover is open.Remedy Close the front cover firmly. If the printer is not online, press [オンライン ].13 ヨウシガ ツマリマシタ Cause

7732 リョウメンインサツ エラー <Auto Error Skip>Cause The printer received data for 2-sided printing of a paper size (including the paper orientation) or p

7 Paper Requirements Usable Paper To ensure optimum performance, use only paper that falls within the specifications in the following lists. Using ina

8 * 1 You can load paper of the following custom paper sizes.- When loading paper in portrait orientation: Width 76.2 to 215.9 mm; Length 127.0 to 35