Canon EOS C300 Mark II Manual de usuario

Wireless File TransmitterWFT-E6 / WFT-E8Guide for EOS C300 Mark II UsersEDIE-0478-000A

10Camera Access Point Connection6To change the [Encryption Key] (password), select [Input] and then press SET. Enter the encryption key (password) th

11When the camera is set to mode, connect the camera to an access point. You can save up to 4 network configuration profiles for different networks

12Wi-Fi Protected Setup (WPS) is the easiest way to connect to a Wi-Fi access point. You can do so simply by pushing a button (if the access point (wi

13Wi-Fi Protected Setup (WPS)1The camera will generate and display an 8-digit PIN code. Enter it into the wireless router’s WPS (PIN code) setup scree

14The camera will automatically detect access points in the vicinity. After you select the desired access point, you only need to enter the selected n

15If you prefer, you can enter manually the details of the Wi-Fi network you want to connect to. Follow the instructions on the screen to complete the

161Select [Automatic] or [Manual] and then press SET. If you selected [Automatic], IP settings will be assigned automatically. Continue with the proc

171Review the access point’s configuration and then press SET. Push the joystick up/down or turn the SELECT dial to review additional settings before

18Initially, basic default network settings for a browser connection are already saved in the camera. You can check these settings on the status scree

19A user name and password are required before the Browser Remote application can access and operate the camera. Initially, basic default user setting

2You can attach a WFT-E6 or WFT-E8 Wireless File Transmitter to the Canon Digital Cinema Camera EOS C300 Mark II to connect the camera to a Wi-Fi netw

20Browser Remote: User Settings4To change the [Password] for the [Full Control User] or [Camera Control User], select [Input] and then press SET. Ent

21You can check the current Wi-Fi network settings using the camera’s [Network Settings] status screens.1Press an assignable button set to [Status].

23Using Network FunctionsAfter completing the preparations in the previous chapter, you can connect the camera via Wi-Fi to any computer or other supp

24After establishing a connection between the camera and a Wi-Fi enabled device1, you can start the Browser Remote application on the device’s Web bro

25Starting Browser Remote5Start the Web browser on the device.6Enter the camera’s URL. Enter the URL from step 2 into the Web browser’s address bar.

26Starting Browser Remote8Select the language for Browser Remote. Click/touch [H] (the language selection button) and select the desired language fro

27In mode, you can select one of the network configuration profiles you have previously configured (up to 4) to connect the camera to the desired Wi

29Troubleshooting

3Introduction 2About this Guide ...

30Check this section if you encounter problems connecting to the Wi-Fi network or accessing the camera remotely from a Wi-Fi enabled device. If the pr

31When using a Wi-Fi network, try the following corrective actions if the transmission rate drops, the connection is lost, or other problems occur. W

32Refer to this list when an error message is displayed on the camera’s screen. Messages are listed alphabetically.If the problem persists, consult a

33Error MessagesUnable to complete WPS. The access point’s encryption method is set to [WEP]. Wi-Fi Protected Setup (WPS) cannot connect to acces

34Error MessagesWi-Fi error. Incorrect encryption method. Make sure the camera and access point are using the same authentication/encryption metho

35IndexAAccess point ... 2, 11Area of use ... Areas of Use and RestrictionsAttaching to a camera ...

36 Windows and Microsoft are trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries. Wi-Fi is a re

DIE-0478-000A © CANON INC. 2016The information in this guide is current as of December 2016. For information on using the transmitter with accessories

4Turn off the camera before attaching the transmitter. The transmitter is powered by the camera. Make sure the camera’s battery pack is sufficiently c

5Network SettingsComplete the network settings using the camera’s menu screens.

6After you connect the camera to a network via Wi-Fi (A 7), you can use the following network functions.Wi-Fi functions and connection types1Connectio

7Before using the network functions, you need to complete the network settings on a camera with the transmitter attached. Once you attach the transmit

8Connecting to a Wi-Fi Network[Manual]If the access point you want to use has stealth mode activated and it cannot be automatically detected by the ca

9When the camera is set to mode, connect a Wi-Fi enabled device using a Camera Access Point connection. Initially, basic default network settings (S