Canon EOS 7D Mark II Manual de usuario

INSTRUCTION MANUAL ENGLISHEOS 7D Mark II (G)  This manual is for the EOS 7D Mark II installed with firmware version 1.1.0 or later. Instruction manu

101Introduction 2Item Check List... 3Instruction Manuals ...

100Autofocusing with 65 points is possible. All the AF area selection modes are selectable.: Dual cross-type AF point. Subject tracking is superior an

101Lenses and Usable AF PointsAutofocusing with 65 points is possible. All the AF area selection modes are selectable.: Cross-type AF point. Subject t

Lenses and Usable AF Points102Autofocusing with only 45 points is possible. (Not possible with all 65 AF points.) All the AF area selection modes are

103Lenses and Usable AF PointsAF is possible with the center AF point and the adjacent AF points above, below, on the left, and on the right. Only the

Lenses and Usable AF Points104Lens Group DesignationsEF-S24mm f/2.8 STM AEF50mm f/2.5 Compact Macro + LIFE SIZE ConverterBEF-S60mm f/2.8 Macro USM BEF

105Lenses and Usable AF PointsEF300mm f/2.8L IS USM + Extender EF2xBEF400mm f/5.6L USM + Extender EF1.4xG (f/8)EF300mm f/2.8L IS II USM A EF500mm f/4L

Lenses and Usable AF Points106EF24-70mm f/2.8L II USM A EF55-200mm f/4.5-5.6 USM DEF24-70mm f/4L IS USM B EF55-200mm f/4.5-5.6 II USM DEF24-85mm f/3.5

107Lenses and Usable AF PointsEF100-200mm f/4.5A BEF100-300mm f/4.5-5.6 USM CEF100-300mm f/5.6 BEF100-300mm f/5.6L BEF100-400mm f/4.5-5.6L IS USM BEF1

108You can easily fine-tune AI Servo AF to suit a particular subject or scene just by selecting an option from case 1 to case 6. This feature is calle

1093 Selecting AI Servo AF CharacteristicsNStandard setting suited for any moving subject. Works with many subjects and scenes.Select [Case 2] to [Cas

11Contents423l Displaying the Grid...74Q Displaying the Electronic Level ...

3 Selecting AI Servo AF CharacteristicsN110Once an AF point starts tracking the subject, this setting enables the camera to consecutively focus on sub

1113 Selecting AI Servo AF CharacteristicsNEven if the target subject moves dramatically up, down, left, or right, the AF point will switch automatica

3 Selecting AI Servo AF CharacteristicsN112Geared for tracking moving subjects whose speed can change dramatically and suddenly. Also, if the target s

1133 Selecting AI Servo AF CharacteristicsN Tracking sensitivitySets the subject-tracking sensitivity during AI Servo AF when an obstacle enters the

3 Selecting AI Servo AF CharacteristicsN114 Acceleration/deceleration trackingThis sets the tracking sensitivity for moving subjects whose speed can

1153 Selecting AI Servo AF CharacteristicsN AF point auto switchingThis sets the switching sensitivity of the AF points as they track the subject mov

3 Selecting AI Servo AF CharacteristicsN116You can manually adjust each case’s three parameters: 1. Tracking sensitivity, 2. Acceleration/deceleration

117With the [22] to [25] menu tabs, you can set the AF functions to suit your shooting style or subject.You can set the AF operation characteristics a

3 Customizing AF FunctionsN118You can set the AF operation characteristics and shutter-release timing during continuous shooting after the first shot

1193 Customizing AF FunctionsNWith the following USM and STM lenses equipped with an electronic focusing ring, you can set whether to use electronic m

Contents1265B: Setting the White Balance ... 168O Custom White Balance...

3 Customizing AF FunctionsN120Enables or disables the AF-assist beam from the built-in flash or EOS-dedicated external Speedlite.ON: EnableThe AF-assi

1213 Customizing AF FunctionsNYou can set the AF operation characteristics and shutter-release timing for One-Shot AF.: Focus priorityThe picture will

3 Customizing AF FunctionsN122If focus cannot be achieved with autofocus, you can have the camera keep searching for the correct focus or have it stop

1233 Customizing AF FunctionsNYou can change the number of manually selectable AF points. If 65-point automatic selection AF is set, the Area AF frame

3 Customizing AF FunctionsN124You can limit the selectable AF area selection modes to suit your shooting preferences. Select the desired selection mod

1253 Customizing AF FunctionsNYou can set the method for changing the AF area selection mode.p/ : S 9 M-Fn buttonAfter you press the <S> button,

3 Customizing AF FunctionsN126: Separate AF pts: Area+ptThe AF area selection mode and AF point (or zone) can be set separately for each camera orient

1273 Customizing AF FunctionsNYou can set the AI Servo AF’s starting AF point for when the AF area selection mode is set to Auto selection: 65 pt AF.:

3 Customizing AF FunctionsN128EOS iTR* AF executes autofocus by recognizing faces and subject colors. EOS iTR AF works when the AF area selection mode

1293 Customizing AF FunctionsNDuring manual AF point selection, the selection can either stop at the outer edge or it can cycle around to the opposite

13Contents978q Selecting the Metering Mode ...224O Setting Exposure Compensation ...

3 Customizing AF FunctionsN130You can set whether or not to display the AF point(s) in the following cases: 1. When selecting the AF point(s), 2. When

1313 Customizing AF FunctionsNYou can set whether the AF points in the viewfinder are to light up in red when focus is achieved.AUTO: AutoThe AF point

3 Customizing AF FunctionsN132The AF status icon indicating AF operation can be displayed in the viewfinder’s field of view or outside the field of vi

133Fine adjustment of the AF’s point of focus is possible for viewfinder shooting. This is called “AF Microadjustment”. Before making the adjustment,

3 Fine Adjustment of AF’s Point of FocusN1344Make the adjustment. Set the adjustment amount. The adjustable range is ±20 steps. Setting it toward “-

1353 Fine Adjustment of AF’s Point of FocusNYou can make the adjustment for each lens and register the adjustment in the camera. You can register the

3 Fine Adjustment of AF’s Point of FocusN136Entering the Serial Number Select the digit to be entered, then press <0> so that <r> appears

1373 Fine Adjustment of AF’s Point of FocusN4Make the adjustment.For a zoom lens, select the wide-angle (W) or telephoto (T) end. Pressing <0>

3 Fine Adjustment of AF’s Point of FocusN138When [ Clear all] appears at the bottom of the screen, pressing the <L> button will clear all the a

139Autofocus can fail to achieve focus (viewfinder’s focus indicator <o> blinks) with certain subjects such as the following:Subjects Difficult

Contents1410Aperture-priority AE ... 316Manual Exposure Shooting...

When Autofocus Fails1401Set the lens’s focus mode switch to <MF>. <4 L> will be displayed on the LCD panel.2Focus on the subject. Focus

141Single and continuous drive modes are provided. You can select the drive mode suiting the scene or subject.1Press the <o> button. (9)2Select

o Selecting the Drive Mode142Q : 10-sec. self-timer/remote controlk: 2-sec. self-timer/remote controlFor self-timer shooting, see page 143. For remote

143Use the self-timer when you want to be in the picture.1Press the <o> button. (9)2Select the self-timer. While looking at the LCD panel or vi

144

1454Image SettingsThis chapter explains image-related function settings: Image-recording quality, ISO speed, Picture Style, white balance, Auto Lighti

146If either a CF card or SD card is already inserted in the camera, you can start recording captured images. When only one card is inserted, you do n

1473 Selecting the Card for Recording and Playback StandardImages will be recorded to the card selected with [Record/play]. Auto switch cardSame as

3 Selecting the Card for Recording and Playback148If [Record func.] is set to [Standard] or [Auto switch card], select the card for recording and play

149You can select the pixel count and the image quality. There are eight JPEG image-recording quality settings: 73, 83, 74, 84, 7a, 8a, b, c. There ar

15Contents13121114Changing Image Playback Settings...394Adjusting the LCD Monitor Brightness ...

3 Setting the Image-Recording Quality150Image-recording Quality Setting Examples73 only61+841+731 only If [–] is set for both RAW and JPEG, 73 will b

1513 Setting the Image-Recording QualityGuide to Image-Recording Quality Settings (Approx.)*1: b is suitable for playing the images on a digital photo

3 Setting the Image-Recording Quality152A RAW image is raw data output by the image sensor converted to digital data. It is recorded to the card as is

1533 Setting the Image-Recording QualityWith Custom Controls, you can assign the image-recording quality to the <B> button or depth-of-field pre

154Set the ISO speed (image sensor’s sensitivity to light) to suit the ambient light level. With the <A> mode selected, the ISO speed will be se

155i: Setting the ISO SpeedN As H1 (equivalent to ISO 25600) and H2 (equivalent to ISO 51200) are expanded ISO speed settings, noise (dots of light,

i: Setting the ISO SpeedN156If the ISO speed is set to “A” (Auto), the actual ISO speed to be set will be displayed when you press the shutter button

157i: Setting the ISO SpeedNYou can set the manually-settable ISO speed range (minimum and maximum limits). You can set the minimum limit within ISO 1

i: Setting the ISO SpeedN158You can set the automatic ISO speed range for Auto ISO within ISO 100 - ISO 16000. You can set the minimum limit within IS

159i: Setting the ISO SpeedNYou can set the minimum shutter speed so that the shutter speed set automatically will not be too slow when Auto ISO is se

Contents161615Reference 467B Button Functions ... 468Checking the Battery Information ...

160By selecting a Picture Style, you can obtain image characteristics matching your photographic expression or the subject.The Picture Style is set au

161A Selecting a Picture StyleND AutoThe color tone will be adjusted automatically to suit the scene. The colors will look vivid, especially for blue

A Selecting a Picture StyleN162V MonochromeCreates black-and-white images.W User Def. 1-3You can register a basic style such as [Portrait], [Landscape

163You can customize a Picture Style by adjusting individual parameters such as [Sharpness] and [Contrast]. To see the resulting effects, take test sh

A Customizing a Picture StyleN1645Set the parameter. Adjust the parameter as desired, then press <0>. Press the <M> button to save the a

165A Customizing a Picture StyleNFor Monochrome, you can also set [Filter effect] and [Toning effect] in addition to [Sharpness] and [Contrast] explai

166You can select a base Picture Style such as [Portrait] or [Landscape], adjust its parameters as desired and register it under [User Def. 1], [User

167A Registering a Picture StyleN6Select a parameter. Select a parameter such as [Sharpness], then press <0>.7Set the parameter. Adjust the pa

168White balance (WB) is for making the white areas look white. Normally, the [Q] (Auto) setting will obtain the correct white balance. If natural-loo

169B: Setting the White BalanceNTo the human eye, a white object looks white regardless of the type of lighting. With a digital camera, the color temp

17PowerCharging the battery  p.38Battery check  p.46Battery informationcheck  p.470Household power outlet  p.474Auto power off  p.69CardFor

B: Setting the White BalanceN1703Import the white balance data. Turn the <5> dial to select the image captured in step 1, then press <0>.

171B: Setting the White BalanceNYou can set the white balance’s color temperature numerically. This is for advanced users.1Select [White balance]. Un

172You can correct the white balance that is set. This adjustment will have the same effect as using a commercially-available color temperature conver

173u White Balance CorrectionNWith just one shot, three images with different color tones can be recorded simultaneously. Based on the color temperatu

u White Balance CorrectionN174 During WB bracketing, the maximum burst for continuous shooting will be lower and the number of possible shots will al

175If the image comes out dark or the contrast is low, the brightness and contrast can be corrected automatically. This function is called Auto Lighti

176This function reduces the noise generated in the image. Although noise reduction is applied at all ISO speeds, it is particularly effective at high

1773 Setting Noise ReductionNCautions for Setting Multi Shot Noise Reduction If there is significant misalignment in the image due to camera shake, t

3 Setting Noise ReductionN178Noise reduction is possible with images exposed for 1 sec. or longer.1Select [Long exp. noise reduction]. Under the [z3]

1793 Setting Noise ReductionN With [Auto] and [Enable], the noise reduction process after the picture is taken may take the same amount of time as th

18Index to FeaturesImage QualityImage-recording quality  p.149ISO speed  p.154Picture Style  p.160White balance  p.168Auto Lighting Optimizer

180You can reduce overexposed highlight areas.1Select [Highlight tone priority]. Under the [z3] tab, select [Highlight tone priority], then press <

181Peripheral light fall-off is a phenomenon that makes the image corners look darker due to the lens characteristics. Color fringing along subject ou

3 Correction of Lens Peripheral Illumination and Aberrations1821Select the setting. Check that [Correction data available] is displayed for the attac

1833 Correction of Lens Peripheral Illumination and AberrationsThe camera already contains data for lens peripheral illumination correction, chromatic

3 Correction of Lens Peripheral Illumination and Aberrations184Cautions for Lens Correction Peripheral illumination correction, chromatic aberration

185If you shoot an image with a fast shutter speed under a light source such as fluorescent light, the blinking of the light source causes flicker and

3 Reducing FlickerN186 If the subject is against a dark background or if there is a bright light in the image, flicker may not be detected. Under ce

187The range of reproducible colors is called “color space”. With this camera, you can set the color space for captured images to sRGB or Adobe RGB. F

188You can freely create and select the folder where the captured images are to be saved.This operation is optional since a folder will be created aut

1893 Creating and Selecting a Folder Select a folder on the folder selection screen, then press <0>. The folder where the captured images will

19Index to FeaturesMovie ShootingMovie shooting  p.313AF method  p.299Movie Servo AF  p.342Movie Servo AF speed  p.345Movie Servo AF tracking

190The file name has four alphanumeric characters followed by a four-digit image number (p.193) and extension. The first four alphanumeric characters

1913 Changing the File Name Operate the <5> dial or <9> to move the and select the desired character. Then press <0> to enter it.

3 Changing the File Name192The first character cannot be an underscore “_”.User setting2When you select the “*** + image size” registered with User se

193The four-digit file number is like the frame number on a roll of film. The captured images are assigned a sequential file number from 0001 to 9999

3 File Numbering Methods194Restarts the file numbering from 0001 each time the card is replaced or a new folder is created.When you replace the card,

195When you set the copyright information, it will be recorded to the image as Exif information.1Select [Copyright information]. Under the [54] tab,

3 Setting Copyright InformationN196When you select [Display copyright info.] in step 2, you can check the [Author] and [Copyright] information that yo

1975GPS SettingsThis chapter explains the camera’s built-in GPS settings. The EOS 7D Mark II (G) can receive satellite navigation signals from GPS sat

198 Geotag information*1 (latitude, longitude, elevation) and coordinated universal time*2 can be appended to images. Using the digital compass (bas

199GPS FeaturesShooting locations and the route traveled can be viewed on a map displayed on a computer, using the Map Utility (EOS software, p.534).V

2The EOS 7D Mark II (G) is a digital single-lens reflex camera featuring a fine-detail CMOS sensor with approx. 20.2 effective megapixels, Dual DIGIC

20Also read “Handling Precautions” on page 529.Camera Care This camera is a precision instrument. Do not drop it or subject it to physical shock. Th

2009Countries and Regions Permitting GPS Function UseUse of GPS function is restricted in some countries and regions, and illegal use may be punishabl

201To acquire GPS signals, take the camera outside where the sky is unobstructed. Face the top of the camera toward the sky while keeping your hands,

Acquiring GPS Signals202 If [Enable] is selected, <r> will still be displayed on the LCD panel even when you turn the camera’s power switch to

203Acquiring GPS Signals1Select [Set up]. Check that [GPS] is set to [Enable]. Select [Set up], then press <0>.2Select [GPS information displa

Acquiring GPS Signals204Play back the images and press the <B> button to display the shooting information screen (p.357). Then tilt <9> up

205The interval (time) to update the geotag information can be set. Although updating the geotag information at shorter intervals will make it more ac

206Camera orientation information (the direction the camera is facing) can be appended to the image.1Select [Set up]. Check that [GPS] is set to [Ena

207Using the Digital CompassWhile you are using the GPS function, if the [Calibrate digital compass] screen appears or if the direction indicated look

Using the Digital Compass2082Move the camera.(1) Swing the camera to the left and right by at least 180°.(2) Tilt the camera up and down by at least 1

209The time information obtained from GPS signals can be set in the camera. The margin of error is approx. ±1 sec.1Select [Set up]. Check that [GPS]

21Handling Precautions Do not block the mirror operation with your finger, etc. Doing so may cause a malfunction. Use a blower to blow away dust on

210When using the GPS logging function, the geotag information of the route the camera traveled is automatically recorded in the camera’s internal mem

211Logging the Route TraveledGeotag information for the route the camera traveled is recorded at the intervals set with [Position update interval] (p.

Logging the Route Traveled212The log data in the camera’s internal memory can be downloaded to a computer with EOS Utility (EOS software) or downloade

213Logging the Route Traveled Use the provided interface cable or one from Canon (p.478). When connecting the interface cable, use the provided cable

214

2156Advanced OperationsIn the <d> <s> <f> <a> <F> shooting modes, you can select the shutter speed, aperture, and other

216The camera automatically sets the shutter speed and aperture to suit the subject’s brightness. This is called Program AE.*<d> stands for Prog

217d: Program AE If the “30"” shutter speed and the lower f/number blink, it indicates underexposure.Increase the ISO speed or use flash. If th

218In this mode, you set the shutter speed and the camera automatically sets the aperture to obtain the standard exposure matching the brightness of t

219s: Shutter-Priority AE If the lower f/number blinks, it indicates underexposure.Turn the <6> dial to set a slower shutter speed until the ap

22Nomenclature<o> Drive mode selection/AF operation/AF method selection button (p.141/86/299)<m> Flash exposure compensation/ISO speed set

220In this mode, you set the desired aperture and the camera sets the shutter speed automatically to obtain the standard exposure suiting the subject

221f: Aperture-Priority AEThe aperture opening (diaphragm) changes only at the moment when the picture is taken. Otherwise, the aperture remains fully

222In this mode, you set both the shutter speed and aperture as desired. To determine the exposure, refer to the exposure level indicator in the viewf

223a: Manual ExposureIf the ISO speed is set to A (AUTO), you can set exposure compensation (p.226) as follows.•[z2: Expo.comp./AEB]• Under [83: Custo

224You can select one of four methods to measure the subject brightness. In the <A> mode, evaluative metering is set automatically.1Press the &l

225q Selecting the Metering ModeNr Spot meteringThis is for metering a specific spot of the subject or scene. Spot metering covers approx. 1.8% of the

226Exposure compensation can brighten (increased exposure) or darken (decreased exposure) the standard exposure set by the camera.Exposure compensatio

227By changing the shutter speed or aperture automatically, the camera brackets the exposure up to ±3 stops in 1/3-stop increments for three successiv

h Auto Exposure Bracketing (AEB)N228 During AEB, <A> in the viewfinder and <h> on the LCD panel will blink. If the drive mode is set to

229Use AE lock when the area of focus is to be different from the exposure metering area or when you want to take multiple shots at the same exposure

23Nomenclature<B> Info button (p.60, 75, 78, 204, 206, 288, 323, 354, 468)<p> AF area selection lever (p.58)LCD panel (p.25-26)Eyecup (p.2

230In this mode, the shutter stays open as long as you hold down the shutter button completely, and closes when you let go of the shutter button. This

231F: Bulb ExposuresYou can preset the bulb exposure’s exposure time. With the bulb timer, you need not hold down the shutter button during the bulb e

F: Bulb Exposures2323Set the desired exposure time. Select the hour, minute, or second. Press <0> so <r> is displayed. Set the desired

233Highlight detail and shadow detail are retained for a high dynamic range of tones even with high-contrast scenes. HDR shooting is effective for lan

w: HDR (High Dynamic Range) ShootingN234 NaturalFor images preserving a wide tonal range where the highlight and shadow details would otherwise be lo

235w: HDR (High Dynamic Range) ShootingN5Set [Continuous HDR]. Select either [1 shot only] or [Every shot], then press <0>. With [1 shot only]

w: HDR (High Dynamic Range) ShootingN2368Take the picture. HDR shooting is possible with viewfinder shooting and Live View shooting. <w> will

237w: HDR (High Dynamic Range) ShootingN When shooting HDR images with [Auto Image Align] set to [Enable], AF point display information (p.359) and D

238You can shoot two to nine exposures to be merged into one image. If you shoot multiple-exposure images with Live View shooting (p.285), you can see

239P Multiple ExposuresN4Set [Multi-expos ctrl]. Select the desired multiple-exposure control method, then press <0>. AdditiveThe exposure of

Nomenclature24Dioptric adjustment knob (p.54)Speaker (for sound)<b/X>Creative Photo/ Comparative playback (Two-image display) button (p.160, 233

P Multiple ExposuresN2406Set the images to be saved. To save all the single exposures and the merged multiple-exposure image, select [All images], th

241P Multiple ExposuresN9Shoot subsequent exposures. When [On:Func/Ctrl] is set, the merged multiple-exposure image will be displayed. With Live Vie

P Multiple ExposuresN242 With multiple exposures, the more exposures there are, the more noticeable the noise, irregular colors, and banding will be.

243P Multiple ExposuresNYou can select an image recorded on the card as the first single exposure. The original of the selected image will remain inta

P Multiple ExposuresN244When [On:Func/Ctrl] is set and you have not finished shooting the set number of exposures, you can press the <x> button

245P Multiple ExposuresN Are there any restrictions on the image-recording quality?All JPEG image-recording quality settings can be selected. If 41 o

246Although using the self-timer or a remote switch can prevent camera shake, using mirror lockup to prevent camera vibrations (mirror shock) can also

247Using the Eyepiece CoverEven if the drive mode is set to continuous shooting, only one shot can be taken. You can also use the self-timer or bulb

248You can connect the Remote Switch RS-80N3 (sold separately) or Timer Remote Controller TC-80N3 (sold separately) or any EOS accessory equipped with

249R Remote Control Shooting4Select the self-timer. While looking at the LCD panel or through the viewfinder, turn the <5> dial to select <Q

25NomenclatureLCD Panel* The display will show only the settings currently applied.Shutter speedFE lock (FEL)Busy (buSY)Built-in flash recycling (buSY

250With the interval timer, you can set the shooting interval and the number of shots. The camera will repeat taking one shot with the set interval un

251H Interval Timer Shooting4Select [OK]. The interval timer settings will be displayed on the menu screen. <H> will be displayed on the LCD p

H Interval Timer Shooting252 If the lens’s focus mode switch is set to <AF>, the camera will not shoot when focus is not achieved. Setting it t

2537Flash PhotographyThis chapter explains how to shoot with the built-in flash and external Speedlites (EX-series, sold separately), how to set flash

254In the <d> <s> <f> <a> <F> modes, just press the <D> button to raise the built-in flash for flash photography.

255D Using the Built-in FlashEffective Range of Built-in Flash(Approx. in meters/feet)ISO SpeedEF-S18-135mm f/3.5-5.6 IS USMEF-S15-85mm f/3-5.6 IS USM

D Using the Built-in Flash256Using the red-eye reduction lamp when taking a flash picture can reduce red eye.1Select [Red-eye reduc.]. Under the [z4]

257D Using the Built-in FlashSet flash exposure compensation if the flash exposure of the subject does not come out as desired. You can set flash expo

D Using the Built-in Flash258FE (flash exposure) lock obtains and locks the appropriate flash exposure for the desired part of the image.1Press the &l

259Flash photography with EX-series Speedlite (sold separately) is as easy as with built-in flash.For detailed instructions, refer to the EX-series Sp

Nomenclature26<J> CF card selection iconISO speed (p.154)<i> ISO speed (p.154)<A> Highlight tone priority (p.180)Exposure level indi

D Using an External Speedlite260 With an EZ/E/EG/ML/TL-series Speedlite set to A-TTL or TTL autoflash mode, the flash can be fired at full output onl

261D Using an External Speedlite If the camera is used with a flash unit or flash accessory dedicated to another camera brand, the camera may not ope

262With the built-in flash or an EX-series, external Speedlite compatible with flash function settings, you can use the camera’s menu screen to set fl

2633 Setting the FlashNYou can set the flash sync speed for flash photography in the aperture-priority AE (f) mode. : AutoThe flash sync speed is set

3 Setting the FlashN264When you use the built-in flash or an external, EX-series Speedlite compatible with flash function settings, you can press the

2653 Setting the FlashN Flash modeNormally, set this to [E-TTL II]. This enables autoexposure shooting with the built-in flash.To set the flash outpu

3 Setting the FlashN266 Shutter synchronizationNormally, set this to [1st curtain] so that the flash fires immediately after the exposure starts.If [

2673 Setting the FlashNThe screen display and setting options will vary depending on the external Speedlite model, current flash mode, Speedlite’s Cus

3 Setting the FlashN268 Wireless functions / Flash ratio controlWireless (multiple) flash shooting is possible with radio or optical transmission.For

2693 Setting the FlashN Shutter synchronizationNormally, set this to [First-curtain synchronization] so that the flash fires immediately after the ex

27NomenclatureViewfinder Information* The display will show only the settings currently applied.Electronic level (p.76)Spot metering circle (p.224)Gri

3 Setting the FlashN270When using second-curtain synchronization, set the shutter speed to 1/25 sec. or slower. If the shutter speed is 1/30 sec. or f

2713 Setting the FlashNFor details on the external Speedlite’s Custom Functions, refer to the Speedlite’s (sold separately) instruction manual.1Select

272The camera’s built-in flash can work as a master unit for Canon EX-series, external Speedlites having a wireless slave feature. It can wirelessly t

273Using Wireless FlashN*1: If the Speedlite does not have a transmission channel setting function, it operates regardless of the channel set on the c

Using Wireless FlashN274The table below shows the possible configurations for wireless flash shooting. Choose the configuration suiting the subject, s

275Using Wireless FlashNThis shows the most basic setup for fully-automatic wireless flash shooting with one external Speedlite.Steps 1 to 4 and 6 app

Using Wireless FlashN2764Set [Flash mode] to [E-TTL II].5Set [Wireless func.] to [0].6Set [Channel]. Set the channel (1-4) to the same one as the sla

277Using Wireless FlashNThis is fully automatic wireless flash shooting with one external Speedlite and the built-in flash.You can change the flash ra

Using Wireless FlashN278Multiple Speedlite slave units can be treated as one flash unit or separated into slave groups whose flash ratio can be set.Th

279Using Wireless FlashN [1(A:B)] Multiple slave units in multiple groupsYou can divide the slave units into groups A and B, and change the flash rat

Nomenclature28<z> Battery check (p.46)<A> AE lock (p.229) AEB in-progress (p.227)<D> Flash-ready (p.254, 259)Improper FE lock warnin

Using Wireless FlashN280 [1(A:B C)] Multiple slave units in multiple groupsThis is a variant of the [1(A:B)] setup. This setup has group C eliminatin

281Using Wireless FlashNThe built-in flash can also be added to wireless flash shooting explained on pages 278-280.The basic settings are shown below.

Using Wireless FlashN282 Flash exposure compensationWhen [Flash mode] is set to [E-TTL II], flash exposure compensation can be set. The flash exposur

283Using Wireless FlashNWhen [Flash mode] is set to [Manual flash], flash exposure can be set manually. The flash output settings that can be set ([1

284

2858Shooting with the LCD Monitor(Live View Shooting)You can shoot while viewing the picture on the camera’s LCD monitor. This is called “Live View sh

2861Set the Live View shooting/Movie shooting switch to <A>.2Display the Live View image. Press the <0> button. The Live View image will

287A Shooting with the LCD MonitorSet [z5: Live View shoot.] (the [z3] tab in <A>) to [Enable].Number of Possible Shots with Live View Shooting

A Shooting with the LCD Monitor288 Each time you press the <B> button, the information display will change.* Refer to the Wi-Fi Adapter W-E1 In

289A Shooting with the LCD Monitor The histogram can be displayed when [z5: Expo. simulation: Enable] (p.296) is set. You can display the electronic

29NomenclatureMode DialYou can set the shooting mode. Turn the Mode Dial while holding down the Mode Dial center (Mode Dial lock release button).A : S

A Shooting with the LCD Monitor290In the <A> shooting mode, the camera detects the scene type and sets everything automatically to suit the scen

291A Shooting with the LCD Monitor*5:Displayed with any of the lenses below:• EF-S18-55mm f/3.5-5.6 IS II • EF-S55-250mm f/4-5.6 IS II• EF300mm f/2.8L

292While the Live View image is displayed, if you press the <n>, <o>, <m>, or <b> button, the setting screen will appear on th

293Shooting Function SettingsIn the <d> <s> <f> <a> <F> modes, the AF method, Drive mode, Metering mode, Recording/playi

294z5When the Live View shooting/Movie shooting switch is set to <A>, the Live View shooting menu options will appear under the [z5] and [z6] ta

2953 Menu Function Settings Grid displayWith [3x3 l] or [6x4 m], you can display grid lines to help you level the camera vertically or horizontally.

3 Menu Function Settings296 Exposure simulationNExposure simulation simulates and displays how the brightness of the actual image (exposure) will loo

2973 Menu Function Settingsz6 N Silent LV shootingN•Mode 1You can suppress the camera noise when shooting. Continuous shooting is also possible. If &

3 Menu Function Settings298 Metering timerNYou can change how long the exposure setting is displayed (AE lock time).Performing any of the following o

299You can select an AF method to suit the shooting conditions and your subject. The following AF methods are provided: [u(face)+Tracking] (p.300), [F

3Before starting, check that all the following items are included with your camera. If anything is missing, contact your dealer.* Battery Charger LC-E

Nomenclature30EF-S18-135mm f/3.5-5.6 IS USM LensFocusing ring (p.140, 308)Focus mode switch (p.50) Zoom position indexContacts (p.529) Lens mount inde

Using AF to Focus (AF Method)300The camera detects and focuses on human faces. If a face moves, the AF point <p> also moves to track the face.1D

301Using AF to Focus (AF Method)4Take the picture. Check the focus and exposure, then press the shutter button completely to take the picture (p.286)

Using AF to Focus (AF Method)302You can focus over a wide area with up to 31 AF points (automatic selection). This wide area can also be divided into

303Using AF to Focus (AF Method)4Take the picture. Check the focus and exposure, then press the shutter button completely to take the picture (p.286)

Using AF to Focus (AF Method)304The camera focuses with a single AF point. This is effective when you want to focus on a particular subject.1Display t

305Using AF to Focus (AF Method)AF Operation Even when focus is achieved, pressing the shutter button halfway will focus again. The image brightness

Using AF to Focus (AF Method)306Shooting Conditions that Make Focusing Difficult Subject with low-contrast such as the blue sky, solid-color flat sur

307Using AF to Focus (AF Method) If you cannot achieve focus with AF, set the lens’s focus mode switch to <MF> and focus manually. If you shoo

308You can magnify the image and focus precisely with MF (manual focus).1Set the lens’s focus mode switch to <MF>. Turn the lens’s focusing rin

309MF: Focusing Manually5Focus manually. While looking at the magnified image, turn the lens’s focusing ring to focus. After achieving focus, press

31NomenclatureEF-S15-85mm f/3.5-5.6 IS USM LensFocus mode switch (p.50) Zoom position indexDistance scaleContacts (p.529) Lens mount index (p.50) Imag

310General Live View Shooting CautionsImage Quality When you shoot at high ISO speeds, noise (such as dots of light and banding) may become noticeabl

311General Live View Shooting CautionsLive View Image Under low- or bright-light conditions, the Live View image may not reflect the brightness of th

312

3139Shooting MoviesMovie shooting is enabled by setting the Live View shooting/Movie shooting switch to <k>. For cards that can record movies,

314When the shooting mode is set to <A>, <d>, or <F>, autoexposure control will take effect to suit the scene’s current brightness.

315k Shooting MoviesWhen the shooting mode is <s>, you can manually set the shutter speed for movie shooting. The ISO speed and aperture will be

k Shooting Movies316When the shooting mode is <f>, you can manually set the aperture for movie shooting. The ISO speed and shutter speed will be

317k Shooting MoviesISO speed in the <A> mode In the <A> mode, the ISO speed will be set automatically within ISO 100 - ISO 16000.ISO Spe

k Shooting Movies318During movie shooting in the <A>, <d>, <s>, <f>, and <F> modes, this camera supports the function th

319k Shooting MoviesDuring movie shooting in the <A> mode, an icon representing the scene detected by the camera will be displayed, and the shoo

Nomenclature32Battery Charger LC-E6Charger for Battery Pack LP-E6N/LP-E6 (p.38).Battery Charger LC-E6ECharger for Battery Pack LP-E6N/LP-E6 (p.38).Bat

k Shooting Movies320You can manually set the shutter speed, aperture, and ISO speed for movie shooting. Using manual exposure to shoot movies is for a

321k Shooting Movies5Focus and shoot the movie. The procedure is the same as steps 3 and 4 for “Autoexposure Shooting” (p.314).ISO Speed in the <a

k Shooting Movies322 Under [ISO speed range], if [Maximum] is set to [H2 (51200)] and you switch from still photo shooting to movie shooting, the max

323k Shooting MoviesEach time you press the <B> button, the information display will change.*1: Applies to a single movie clip.*2: Refer to the

k Shooting Movies324You can display the electronic level by pressing the <B> button (p.75).  Note that if the AF method is set to [u +Tracking

325k Shooting MoviesNotes for Movie Shooting Movie-related settings are under the [z4] and [z5] tabs (p.342). In the <A> mode, they are under t

k Shooting Movies326The final image simulation shows the results of the current settings for Picture Style, white balance and other functions in the i

327k Shooting MoviesWhile shooting a movie, you can also take a still photo by pressing the shutter button completely.Taking Still Photos During Movie

k Shooting Movies328 If L 8 (59.94 fps) or 7 (50.00 fps) is set, or if [z5: V button function] is set to [ /k] or [q/k], you cannot take still photos

329If you press the <n>, <o>, <m>, or <b> button while the image is displayed on the LCD monitor, the setting screen will appe

33NomenclaturePass the end of the strap through the camera’s strap mount eyelet from the bottom. Then pass it through the strap’s buckle as shown in t

3 Setting the Movie Recording Size330To select the card for recording/playing back, WB Shift/Bracketing, or Picture Style parameters, press the <B

3313 Setting the Movie Recording SizeYou can select the movie’s size, frame rate, and compression method. Image SizeL 1920x1080Full High-Definition (

3 Setting the Movie Recording Size332 Compression MethodW ALL-I (For editing/I-only)Compresses one frame at a time for recording. Although the file s

3333 Setting the Movie Recording SizeRecords the movie at a frame rate of 24.00 fps. Applies to Full HD quality.If [Enable] is set, the movie is recor

3 Setting the Movie Recording Size334 In MOV Format (Approx.) In MP4 Format (Approx.)Total Movie Recording Time and File Size Per MinuteMovie Record

3353 Setting the Movie Recording Size Movie Files Exceeding 4 GBEven if you shoot a movie exceeding 4 GB, you can keep shooting without interruption.

336You can shoot movies while recording sound with the built-in monaural microphone or the Directional Stereo Microphone DM-E1 (sold separately). You

3373 Setting the Sound Recording Using a microphoneNormally, the built-in microphone will record monaural sound.Stereo sound recording is also possib

338You can change the settings of the ISO speed, sound-recording level, etc., without making too much noise while shooting a movie.When [z5: Silent Co

339The time code is a time reference recorded automatically to synchronize the movie during movie shooting. It is recorded at all times in the followi

Nomenclature34When connecting the camera to a computer, printer or Wireless File Transmitter, use the provided interface cable or one from Canon (show

3 Setting the Time Code340You can select what to display on the movie shooting screen.Rec time : Indicates the elapsed time from the start of the movi

3413 Setting the Time Code Time codeThe time code can be appended to a movie that is output via HDMI (p.350).Enable: Appends time code to HDMI output

342z4When the Live View shooting/Movie shooting switch is set to <k>, the movie shooting menu options will appear under the [z4] and [z5] tabs (

3433 Menu Function Settings• If you want to keep the focus at a specific point or you do not want the lens operation noise to be recorded, you can tem

3 Menu Function Settings344 Grid displayWith [3x3 l] or [6x4 m], you can display grid lines to help you level the camera vertically or horizontally.

3453 Menu Function Settings Movie Servo AF speedNYou can set the Movie Servo AF’s AF speed and its operation conditions.This function is settable whe

3 Menu Function Settings346 Movie Servo AF tracking sensitivityNYou can change the Movie Servo AF’s tracking sensitivity to one of five levels. This

3473 Menu Function Settingsz5 Silent LV shootingNThis function applies to still photo shooting. For details, see page 297. Metering timerNYou can ch

3 Menu Function Settings348 V button functionYou can set the functions performed by pressing the shutter button halfway or completely during movie sh

3493 Menu Function Settings[Mirroring]• The movie is displayed on the LCD monitor and via the HDMI output simultaneously.• The HDMI output movie does

35NomenclatureUsing a Genuine Interface Cable (sold separately)If you use a genuine interface cable (sold separately, p.478), run the cable through th

3 Menu Function Settings35053 HDMI frame rateFor HDMI output, you can set the frame rate to [Auto], [59.94i]/[50.00i], [59.94p]/[50.00p], or [23.98p]

351General Movie Shooting CautionsWhite <s> and Red <E> Internal Temperature Warning IconsIf the camera’s internal temperature increases

352General Movie Shooting CautionsRecording and Image Quality If you use a card with a slow writing speed, a five-level indicator may appear on the r

35310Image PlaybackThis chapter explains how to play back or erase photos and movies, how to display them on a TV screen, and other playback-related f

3541Play back the image. Press the <x> button. The last image captured or played back will appear.2Select an image. To play back images start

355x Image Playback3Exit the image playback. Press the <x> button to exit the image playback and return to shooting-ready state.With the shooti

356 Basic information display* Refer to the Wi-Fi Adapter W-E1 Instruction Manual.B: Shooting Information DisplaySample Information for Still PhotosS

357B: Shooting Information Display Shooting information display • Detailed information* When you shoot in RAW+JPEG image quality, the RAW image file

B: Shooting Information Display358• Lens/Histogram information• GPS informationHistogram display (Brightness)Lens nameFocal lengthHistogram display (R

359B: Shooting Information Display• < > and < > modes: Shutter speed, aperture and ISO speed are not displayed.• < > mode: Aperture

Nomenclature36Wi-Fi Adapter W-E1This adapter is an accessory that enables Wi-Fi (wireless communication) functions when installed in the SD card slot

B: Shooting Information Display360 HistogramThe brightness histogram shows the exposure level distribution and overall brightness. The RGB histogram

361You can search for images quickly with the index display showing 4, 9, 36, or 100 images on one screen.1Press the <u> button. During image p

x Searching for Images Quickly362In the single-image display, you can turn the <6> dial to jump through the images forward or backward according

363x Searching for Images Quickly3Browse by jumping. Press the <x> button to play back images. In the single-image display, turn the <6>

364You can magnify a captured image by approx. 1.5x to 10x on the LCD monitor.1Magnify the image. The image can be magnified as follows: 1. During im

365u Magnifying ImagesUnder the [33] tab, when you select [Magnificatn (apx)], you can set the starting magnification and initial position for the mag

366You can compare two images side by side on the LCD monitor. In the two-image display, you can use magnified view or jump display as well as protect

367You can rotate the displayed image to the desired orientation.1Select [Rotate image]. Under the [31] tab, select [Rotate image], then press <0&

368Protecting an image prevents it from being erased accidentally.1Select [Protect images]. Under the [31] tab, select [Protect images], then press &

369K Protecting ImagesYou can protect all the images in a folder or on a card at once.When you select [All images in folder] or [All images on card] i

371Getting StartedThis chapter explains preparatory steps before you start shooting and basic camera operations.Minimizing Dust When changing lenses,

K Protecting Images370During image playback, you can use the <c> button to protect an image.1Select [m btn function]. Under the [53] tab, selec

371You can rate images (still photos and movies) with one of the five rating marks: l/m/n/o/p. This function is called rating.1Select an image. Durin

Setting Ratings3721Select [Rating]. Under the [32] tab, select [Rating], then press <0>.2Select an image. Turn the <5> dial to select an

373Setting RatingsA total of up to 999 images of a given rating can be displayed. If there are more than 999 images with a given rating, [###] will be

374During playback, you can press the <Q> button to set the following: [J: Protect images], [b: Rotate image], [9: Rating], [R: RAW image proces

375Q Quick Control for PlaybackTo rotate an image, set [51: Auto rotate] to [OnzD]. If [51: Auto rotate] is set to [OnD] or [Off], the [b Rotate image

376You can play back movies in the following three ways:By connecting the camera to a TV set with HDMI Cable HTC-100 (sold separately), you can play b

377k Enjoying MoviesThe movie files recorded on the card can be transferred to a computer and played back or edited with pre-installed or general-purp

3781Play back the image. Press the <x> button to display an image.2Select a movie. Turn the <5> dial to select the movie to be played.

379k Playing MoviesMovie Playback PanelOperation Playback Description7 Play Pressing <0> toggles between play and stop.8 Slow motionAdjust the s

381Remove the protective cover. Detach the protective cover provided with the battery.2Attach the battery. As shown in the illustration, attach the

380You can edit out the first and last scenes of a movie in approx. 1-sec. increments.1On the movie playback screen, select [X]. The movie editing pa

381X Editing a Movie’s First and Last Scenes4Save the edited movie. Select [W], then press <0>. The save screen will appear. To save it as a

382You can play back the images on the card as an automatic slide show.1Select [Slide show]. Under the [32] tab, select [Slide show], then press <

3833 Slide Show (Auto Playback)3Configure [Set up] as desired. Select [Set up], then press <0>. Set the [Display time] and [Repeat] settings f

3 Slide Show (Auto Playback)3844Start the slide show. Select [Start], then press <0>. After [Loading image...] is displayed, the slide show wi

385By connecting the camera to a TV set with an HDMI cable (sold separately), you can play the camera’s still photos and movies on the TV set. For the

Viewing Images on a TV Set386If the TV set connected to the camera with an HDMI cable is compatible with HDMI CEC*, you can use the TV set’s remote co

387Viewing Images on a TV Set3Press the camera’s <x> button. An image will appear on the TV screen and you can use the TV set’s remote control

388The images recorded on one card can be copied to another card.1Select [Image copy]. Under the [31] tab, select [Image copy], then press <0>.

389a Copying Images 4Select the images to be copied. Turn the <5> dial to select an image to be copied, then press <0>. The [X] icon wil

39Charging the Battery Upon purchase, the battery is not fully charged.Charge the battery before use.Recharge the battery on the day before or on th

a Copying Images3908Select [OK]. Check the information of the source card and target card, then select [OK]. The copying will start and the progress

391a Copying Images The file name of the copied image will be the same as the source image’s file name. If [Sel.Image] is set, you cannot copy image

392You can either select and erase unnecessary images one by one or erase them in one batch. Protected images (p.368) will not be erased.Once an image

393L Erasing Images2Select [Select and erase images]. An image will be displayed. If you press the <u> button and turn the <6> dial coun

394The LCD monitor’s brightness is adjusted automatically for optimum viewing depending on the ambient light level. You can also set the automatic adj

395Changing Image Playback SettingsVertical images are rotated automatically so they are displayed vertically on the camera’s LCD monitor and on the c

396

39711Post-ProcessingImagesYou can process RAW images with the camera or resize (reduce the resolution of) JPEG images. A M icon at the upper right of

398You can process 1 images with the camera and save them as JPEG images. As the RAW image itself does not change, you can apply different processing

399R Processing RAW Images with the CameraNDisplaying the setting screen Press <0> to display the setting screen. Turn the <5> or <6&g

4* Detailed Instruction Manuals (PDF files) can be downloaded from the Canon website (see below).1 Download the Instruction Manuals (PDF files). Conn

40Load a fully-charged Battery Pack LP-E6N (or LP-E6) into the camera. The camera’s viewfinder becomes bright when a battery is installed, and darkens

R Processing RAW Images with the CameraN400 Brightness adjustmentYou can adjust the image brightness up to ±1 stop in 1/3-stop increments. The displ

401R Processing RAW Images with the CameraN Color space (p.187)You can select either sRGB or Adobe RGB. Since the camera’s LCD monitor is not compat

R Processing RAW Images with the CameraN402Peripheral Illumination Correction, Distortion Correction, and Chromatic Aberration CorrectionTo execute pe

403You can resize a JPEG image to make the pixel count lower and save it as a new image. Resizing an image is possible only with JPEG 3/4/a/b images.

S Resizing JPEG Images404Resize Options by Original Image SizeImage sizes by aspect ratio are shown in the table below. The image-recording quality fi

40512Sensor CleaningThe camera has a Self Cleaning Sensor Unit to automatically shake off dust adhered to the image sensor’s front layer (low pass fil

406Whenever you set the power switch to <1> or <2>, the Self Cleaning Sensor Unit operates to automatically shake off the dust on the fron

407Normally, the Self Cleaning Sensor Unit will eliminate most of the dust that may be visible on captured images. However, in case visible dust still

3 Appending Dust Delete DataN4083Shoot a solid-white object. At a distance of 20 cm - 30 cm (0.7 ft. - 1.0 ft.), fill the viewfinder with a patternle

409Dust that could not be removed by the automatic sensor cleaning can be removed manually with a commercially-available blower, etc. Before cleaning

41The camera can use a CF card and an SD card. Images can be recorded when at least one card is installed in the camera.If both types of card are inse

3 Manual Sensor CleaningN410 While cleaning the sensor, never do any of the following. If the power is cut off, the shutter will close and the shutte

41113Printing Images and TransferringImages to a Computer Printing (p.414)You can connect the camera directly to a printer and print out the images o

412The direct printing procedure can be performed entirely with the camera while you look at the camera’s LCD monitor.1Set the camera’s power switch t

413Preparing to Print6Play back the image. Press the <x> button. The image will appear with the <w> icon on the upper left of the screen

414The screen display and setting options will differ depending on the printer. Some settings may not be available. For details, refer to the printer’

415w Printing Select the size of the paper loaded in the printer, then press <0>. The paper type screen will appear. Select the type of the p

w Printing4164Set the printing effects.Set them if necessary. If you do not need to set any printing effects, go to step 5. Contents displayed on th

417w Printing5Set the date and file number imprinting. Set them if necessary. Select <I>, then press <0>. Set the print settings as des

w Printing418In step 4 on page 416, select the printing effect. When the <ze> icons are displayed brightly, you can press the <B> button.

419w PrintingYou can crop the image and print only an enlarged version of the cropped portion, as if the image is recomposed.Set the cropping right be

Installing and Removing the Card423Close the cover. Close the cover and slide it in the direction shown by the arrows until it snaps shut. When you

w Printing420 If the image’s aspect ratio is different from the printing paper’s aspect ratio, the image may be cropped significantly when you print

421You can set the print type, date imprinting, and file number imprinting. The print settings will be applied to all print-ordered images. (They cann

W Digital Print Order Format (DPOF)4224 Exit the setting. Press the <M> button. The print order screen will reappear. Next, select [Sel.Image

423W Digital Print Order Format (DPOF) Sel.ImageSelect and order images one by one.If you press the <u> button and turn the <6> dial coun

424With a PictBridge printer, you can easily print images with DPOF.1 Prepare to print.See page 412.Follow the “Connecting the Camera to a Printer” p

425You can connect the camera to a computer and operate the camera to transfer images on the card to the computer. This is called direct image transfe

d Transferring Images to a Computer4263Set the camera’s power switch to <1>. When the computer displays a screen to select the program, select

427d Transferring Images to a Computer Sel.Image1Select [Image transfer]. Under the [32] tab, select [Image transfer], then press <0>.2Select

d Transferring Images to a Computer4285Transfer the image.On the computer screen, check that EOS Utility’s main window is displayed. Select [Direct

429You can specify up to 998 images to be printed in a photobook. When you use EOS Utility (EOS software) to transfer images to a computer, the specif

43Installing and Removing the Card1Open the cover. Set the power switch to <2>. Make sure the access lamp is off, then open the cover. If [Re

p Specifying Images for a Photobook430You can specify all the images in a folder or on a card at once.When [x1: Photobook Set-up] is set to [All image

43114Customizing theCameraYou can customize various camera functions to suit your picture-taking preferences with Custom Functions.Also, current camer

4323 Custom FunctionsN81: ExposureA LV Shootingk Movie ShootingExposure level incrementsp.434k kISO speed setting increments k In aBracketing auto can

4333 Custom FunctionsNSelecting [85: Clear all Custom Func. (C.Fn)] will clear all the Custom Function settings.83: Display/OperationA LV Shootingk Mo

434Under the [8] tab, you can customize various camera features to suit your picture-taking preferences. Any settings different from the default will

4353 Setting Custom FunctionsNBracketing sequenceThe AEB shooting sequence and white balance bracketing sequence can be changed.0-+: 0, -, +-0+: -, 0,

3 Setting Custom FunctionsN436Safety shiftOFF: DisableTv/Av: Shutter speed/ApertureThis takes effect in the shutter-priority AE (s) and aperture-prior

4373 Setting Custom FunctionsNSame exposure for new apertureIf the <a> mode (manual exposure shooting) is set and the ISO speed is set manually

3 Setting Custom FunctionsN438C.Fn2: Exposure/DriveSet shutter speed rangeYou can set the shutter speed range. In the <s> <a> modes, you c

4393 Setting Custom FunctionsNContinuous shooting speedYou can set the continuous shooting speed for <o> high-speed continuous shooting, <i&g

Installing and Removing the Card44 When the access lamp is lit or blinking, it indicates that images are being written to, read from, or erased from

3 Setting Custom FunctionsN440C.Fn3: Display/Operation Focusing ScreenTo suit your shooting needs, you can change to an optional focusing screen, sold

4413 Setting Custom FunctionsNWarnings z in viewfinderWhen any of the following functions are set, the <z> icon can be displayed in the viewfind

3 Setting Custom FunctionsN442Dial direction during Tv/Av : Normal : Reverse directionDial turning direction when setting the shutter speed and apertu

4433 Setting Custom FunctionsNC.Fn4: OthersAdd cropping informationIf you set cropping information, vertical lines for the aspect ratio you have set w

3 Setting Custom FunctionsN444Default Erase optionDuring image playback and image review after image capture, when you press the <L> button, the

445You can assign often-used functions to camera buttons or dials according to your preferences.1Select [83: Custom Controls]. Under the [83] tab, se

83: Custom ControlsN446Assignable Functions to Camera ControlsFunctionPageMetering and AF start 450 k k*1k*1AF stop452kkSwitch to registered AF functi

44783: Custom ControlsN* The AF stop button ( ) is provided only on super telephoto IS lenses.* pkkkk*2k*2k kk*3k*3k*4k k*5kkkkk kk k k kk kkkkkkk kk

83: Custom ControlsN448FunctionPageOne-touch image quality setting456One-touch image quality (hold)Image qualityPicture Style 457Depth-of-field previe

44983: Custom ControlsN* The AF stop button ( ) is provided only on super telephoto IS lenses.* pk*6k*6k*6k*6kkkkkkkkkkkk k k k k k

45If you turn on the power switch and the date/time/zone setting screen appears, see page 47 to set the date/time/zone.<1> : The camera turns on

83: Custom ControlsN450When you press the button assigned to this function, metering and AF are executed.*1:When assigned to the <p> or <A>

45183: Custom ControlsN AI Servo AF characteristics (p.108)Press the <p> or <A> button to perform AF with the set case from [Case1] to [C

83: Custom ControlsN452The AF will stop while you hold down the button assigned to this function. Convenient when you want to stop the AF during AI Se

45383: Custom ControlsNDuring metering, tilting <p> to the right will switch between the current AF point and the center AF point or registered

83: Custom ControlsN454When you press the shutter button halfway, only the exposure metering is performed.When you press the button assigned to this f

45583: Custom ControlsNYou can set the ISO speed by holding down <0> and turning the <6> dial.If this control is used while Auto ISO is se

83: Custom ControlsN456In manual exposure <a>, you can set the aperture with the <5> or <6> dial.Pressing the button assigned to thi

45783: Custom ControlsNPress <0> to display the Picture Style selection setting screen on the LCD monitor (p.160).When you press the depth-of-fi

83: Custom ControlsN458Pressing <0> will play back images.Press <0> to magnify or reduce the images recorded on the card. See page 364 for

459Under My Menu tab, you can register menu items and Custom Functions whose settings you change frequently. You can also name the registered menu tab

Turning on the Power46When the power switch is set to <1>, the battery level will be indicated in one of six levels. A blinking battery icon (b)

3 Registering My MenuN4602Select [Select items to register].3Register the desired items. Select the desired item, then press <0>. Select [OK]

4613 Registering My MenuN Delete tabYou can delete the My Menu tab currently displayed. Select [Delete tab] to delete the [MY MENU*] tab. Rename tab

3 Registering My MenuN462You can delete all My Menu tabs and delete all My Menu items. Delete all My Menu tabsYou can delete all My Menu tabs. When y

4633 Registering My MenuNYou can select [Menu display] to set the menu screen that is to appear first when you press the <M> button. Normal dis

464You can register current camera settings, such as the shooting mode, menu functions, and Custom Function settings, as Custom shooting modes under t

465w: Registering Custom Shooting ModesN Shooting functionsShooting mode, Shutter speed, Aperture, ISO speed, AF operation, AF area selection mode, A

w: Registering Custom Shooting ModesN466[24] Lens drive when AF impossible, Selectable AF point, Select AF area selection mode, AF area selection meth

46715ReferenceThis chapter provides reference information for camera features, system accessories, etc.Certification LogoSelect [54: Certification Log

468If you press the <B> button when the camera is ready to shoot, the screens for the [Displays camera settings], [Electronic level] (p.75), and

469B Button Functions* Refer to the Wi-Fi Adapter W-E1 Instruction Manual.Pressing the <Q> button enables Quick Control of the shooting setting

47When you turn on the power for the first time or if the date/time/zone are reset, the date/time/zone setting screen will appear. Follow the steps be

470You can check the battery’s condition on the LCD monitor. Each Battery Pack LP-E6N/LP-E6 has a unique serial number, and you can register multiple

4713 Checking the Battery InformationYou can register up to six LP-E6N/LP-E6 battery packs to the camera. To register multiple battery packs to the ca

3 Checking the Battery Information472It is convenient to label all registered Battery Pack LP-E6N/LP-E6 with their serial numbers, using commercially-

4733 Checking the Battery InformationYou can check the remaining capacity of any battery pack (even when not installed) and also when it was last used

474You can power the camera with a household power outlet by using the DC Coupler DR-E6 and AC Adapter AC-E6N (both sold separately).1Connect the DC C

475With a commercially-available Eye-Fi card already set up, you can automatically transfer captured images to a computer, or upload them to an online

H Using Eye-Fi Cards4764Display the connection information. Select [Connection info.], then press <0>.5Check the [Access point SSID:]. Check t

477H Using Eye-Fi CardsCautions for Using Eye-Fi Cards If “ ” is displayed, an error occurred while retrieving the card information. Turn the camera’

478System MapST-E2 270EX II 600EX II-RT 430EX III-RT/ 430EX III ST-E3-RT Macro Ring Lite MR-14EX II Macro Twin Lite MT-24EX Angle Finder C Hand Str

479System Map*1: Battery Pack LP-E6 can also be used. *2: To use the older model WFT-E7 (not Version 2), the firmware must be updated and Interface

3 Setting the Date, Time, and Zone484Set the date and time.Turn the <5> dial to select the number. Press <0> so <r> is displayed.

480o: Set automatically k: User selectable : Not selectable/DisabledFunction Availability Table According to Shooting ModeStill Photo ShootingFunc

481Function Availability Table According to Shooting Mode*1: If the built-in flash is set to <b>, the AF-assist beam will not be emitted.*2: Set

Function Availability Table According to Shooting Mode482o: Set automatically k: User selectable : Not selectable/Disabled*1 : The z icon indicate

483Function Availability Table According to Shooting Mode*3 : With Auto ISO, you can set a fixed ISO speed.*4 : With Auto ISO, you can set exposure co

484z: Shooting 1 (Red) PageMenu SettingsViewfinder Shooting and Live View ShootingImage quality1 / 41 / 6114973 / 83 / 74 / 84 / 7a / 8a / b / cImage

485Menu Settingsz: Shooting 2 (Red) Page* During movie shooting, [Expo.comp./AEB] will be [Exposure comp.].z: Shooting 3 (Red)Exposure compensation/AE

Menu Settings486z: Shooting 4* (Red) Page* In the <A> mode, these menu options are displayed under [z2].z: Shooting 5* (Red)* In the <A> m

487Menu Settings2: AF1 (Purple) Page2: AF2 (Purple)2: AF3 (Purple)Case 1 Versatile multi purpose setting 109Case 2Continue to track the subjects, igno

Menu Settings4882: AF4 (Purple) Page2: AF5 (Purple)Lens drive when AF impossibleContinue focus search / Stop focus search 122Selectable AF point 65 po

489Menu Settings3: Playback 1 (Blue) Page3: Playback 2 (Blue)3: Playback 3 (Blue)* The setting is linked to the [Time code]’s [Movie play count] under

493 Selecting the Interface Language The date/time that were set will start from when you press <0> in step 6. In step 3, the time displayed o

Menu Settings4905: Set-up 1 (Yellow) Page5: Set-up 2 (Yellow)Record function+card/folder selectionRecord function:Standard / Auto switch card / Record

491Menu Settings5: Set-up 3 (Yellow) Page* Options displayed on the screen differ depending on the [Video system] setting.5: Set-up 4 (Yellow)Video sy

Menu Settings4928: Custom Functions (Orange) Page9: My Menu (Green)C.Fn1: ExposureCustomize camera functions as desired434C.Fn2: Exposure/Drive 438C.F

493Menu Settingsz: Shooting 4*1 (Movie) (Red) Page* In the <A> mode, these menu options are displayed under [z2].* In the <A> shooting mod

Menu Settings494z: Shooting 5*1 (Movie) (Red) Page*1: In the <A> mode, these menu options are displayed under [z3].*2: The setting is linked to

495If a problem occurs with the camera, first refer to this Troubleshooting Guide. If this Troubleshooting Guide does not resolve the problem, contact

Troubleshooting Guide496If the power is turned off while an image is being recorded to the card, the access lamp will remain on or continue to blink

497Troubleshooting GuideDuring interval timer shooting, auto power off will not take effect (p.250). The camera cannot be used with EF-M lenses (p.5

Troubleshooting Guide498 If [z4: Mirror lockup] is set to [Enable], set it to [Disable]. Set the lens’s focus mode switch to <AF> (p.50). Pre

499Troubleshooting Guide During Live View shooting and movie shooting, the AF control method (phase-difference detection with the image sensor or con

5The camera can use the following cards regardless of capacity: If the card is new or was previously formatted by another camera or computer, format t

50The camera is compatible with all Canon EF and EF-S lenses. The camera cannot be used with EF-M lenses.1Remove the caps. Remove the rear lens cap a

Troubleshooting Guide500 If [z3: Highlight tone priority] is set to [Enable], the settable ISO speed range will be ISO 200 - ISO 16000. Even if you e

501Troubleshooting Guide When the image-recording quality is set to 41 or 61, the multiple-exposure image will be recorded in 1 quality (p.245). If

Troubleshooting Guide502 If you use a flash unit other than an EX-series Speedlite, the flash will always be fired at full output (p.260). When the

503Troubleshooting Guide If the card’s writing speed is slow, movie shooting may stop automatically. For cards that can record movies, see page 5. To

Troubleshooting Guide504 Flickering, horizontal stripes (noise), or irregular exposures can be caused by fluorescent lighting, LED lighting, or other

505Troubleshooting Guide Set the <R> switch to the left (lock release, p.59). Check the [83: Multi function lock] setting (p.442). Check the

Troubleshooting Guide506 Check that the correct date and time are set (p.47). Check the time zone and daylight saving time (p.47-48). The shooting

507Troubleshooting Guide [33: Highlight alert] is set to [Enable] (p.359). [33: AF point disp.] is set to [Enable] (p.359). If the image is protect

Troubleshooting Guide508 Set the [53: Video system] correctly to [For NTSC] or [For PAL]. Check that the HDMI cable’s plug is inserted all the way i

509Troubleshooting Guide If you selected [Clean nowf], the shutter will make a noise, but no picture is taken (p.406). If you repeatedly turn the po

51Attaching and Detaching a LensTurn the zoom ring on the lens with your fingers. If you want to zoom, do it before focusing. Turning the zoom ring a

510If there is a problem with the camera, an error message will appear. Follow the on-screen instructions.* If the error still persists, write down th

511•TypeType: Digital, single-lens reflex, AF/AE camera with built-in flashRecording media: CF cards (Type I, UDMA 7 supported)SD/SDHC*/SDXC* memory c

Specifications512White balance:Auto, Preset (Daylight, Shade, Cloudy, Tungsten light, White fluorescent light, Flash), Custom, Color temperature setti

513SpecificationsAF area selection mode: Single-point Spot AF (manual selection), Single-point AF (manual selection), AF point expansion (manual selec

Specifications514AE lock: Auto: Applied in One-Shot AF mode with evaluative metering when focus is achievedManual: By AE lock buttonInterval timer: Sh

515Specifications•FlashBuilt-in flash: Retractable, auto pop-up flashGuide number: Approx. 11/36.1 (ISO 100, in meters/feet)Flash coverage: Approx. 15

Specifications516Compression method: ALL-I (For editing/I-only), IPB (Standard), IPB (Light)* IPB (Light) is for MP4 only.File size: [MOV]• Full HD (5

517Specifications[SD card]ALL-I: 20 MB/sec. or fasterIPB (Standard), Full HD 59.94p/50.00p: 20 MB/sec. or fasterIPB (Standard), other than above: 6 MB

Specifications518•LCD MonitorType: TFT color, liquid-crystal monitorMonitor size and dots: Wide 7.7 cm (3.0-in) (3:2) with approx. 1.04 million dotsBr

519Specifications• Direct PrintingCompatible printers: PictBridge-compatible printersPrintable images: JPEG and RAW imagesPrint ordering: DPOF Version

Attaching and Detaching a Lens52A lens hood can block unwanted light and prevent rain, snow, dust, etc. adhering to the front of the lens. Before stor

Specifications520•PowerBattery: Battery Pack LP-E6N/LP-E6, quantity 1* AC power usable with household power outlet accessories.* With Battery Grip BG

521

522

523Trademarks Adobe is a trademark of Adobe Systems Incorporated. Microsoft and Windows are trademarks or registered trademarks of Microsoft Corpora

524Use of Genuine Canon Accessories Is RecommendedThis product is designed to achieve excellent performance when used with genuine Canon accessories.C

525The following precautions are provided to prevent harm or injury to yourself and others. Make sure to thoroughly understand and follow these precau

Safety Precautions526 When the camera or accessories are not in use, make sure to remove the battery and disconnect the power plug from the equipment

527Safety Precautions Cautions:Follow the cautions below. Otherwise, physical injury or property damage may result. Do not use or store the product

528Only for European Union and EEA (Norway, Iceland and Liechtenstein)These symbols indicate that this product is not to be disposed of with your hous

529LCD Panel and LCD Monitor Although the LCD monitor is manufactured with very high precision technology with over 99.99% effective pixels, there ma

53When you use the IS lens’s built-in Image Stabilizer, camera shake is corrected to obtain a sharper shot. The procedure explained here is based on t

530

53116Downloading Images toa Computer / SoftwareThis chapter explains how to transfer images from the camera to a computer, gives an overview of the so

532You can use EOS software to download the images in the camera to your computer. There are two ways to do this.1Install the software (p.536).2Use th

533Downloading Images to a ComputerYou can use a card reader to download images to your computer.1Install the software (p.536).2Insert the card into t

534EOS Solution DiskThis disk contains various software for EOS cameras.Communication Software for the Camera and Computer You can download images (s

535About the Software Downloading from the Canon websiteYou can download the following software and Software Instruction Manuals from the Canon websi

536Compatible OS 1 Insert the EOS Solution Disk into the computer.2 Click [Easy Installation] and follow the on-screen instructions to install.3 After

537Installing the SoftwareCompatible OS 1 Insert the EOS Solution Disk into the computer.On your computer’s desktop, double-click and open the CD-ROM

538IndexNumerics10- or 2-sec. self-timer...1431280x720 (movie)...3311920x1080 (movie)...33124

539IndexCW (Custom shooting) ...464Cable...3, 385, 412, 425, 478, 532Protector ...34CameraCamera

54Turn the dioptric adjustment knob. Turn the knob left or right so that the AF points in the viewfinder look sharp. If the knob is difficult to tur

540IndexExposure simulation ...296External Speedlite 9 FlashEyecup... 247Eye-Fi cards...

541IndexImage dust prevention ...405Image-recording quality ...149, 330Image review time...70Image Stabili

542IndexLog data ...211Long exposure noise reduction...178Long exposures ...230Low-speed co

543IndexNNoise reductionHigh ISO speed ...176Long exposures ...178Nomenclature...

544IndexSepia (Monochrome) ...165Sharpness...164Shooting function settings...60, 469Shooting in

545

CANON INC.30-2 Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, JapanEurope, Africa & Middle EastCANON EUROPA N.V.Bovenkerkerweg 59, 1185 XB Amstelve

55Basic OperationThe shutter button has two steps. You can press the shutter button halfway. Then you can further press the shutter button completely.

Basic Operation56Turn the dial while holding down the lock release button at the center of the dial.Use it to set the shooting mode.(1)After pressing

57Basic Operation(1)After pressing a button, turn the <5> dial.When you press a button such as <n> <o> <m>, the respective fun

Basic Operation58The <p> lever can be tilted to the right. Use it to select the AF area selection mode.After pressing the <S> button, tilt

59Basic OperationDuring movie shooting, the touch pad provides a quiet way to adjust the shutter speed, aperture, exposure compensation, ISO speed, so

6Quick Start Guide1Insert the battery (p.40).To charge the battery, see page 38.2Insert the card (p.41).The camera-front side slot is for a CF card,

Basic Operation60Turn on (9) or off the LCD panel illumination by pressing the <U> button. During a bulb exposure, pressing the shutter button c

61You can directly select and set the shooting functions displayed on the LCD monitor. This is called Quick Control.1Press the <Q> button (7).

Q Quick Control for Shooting Functions62Settable Functions on Quick Control ScreenShutter speed (p.218)AF operation (p.86)White balance correction /Wh

63Q Quick Control for Shooting Functions Select a function and press <0>. The function setting screen will appear. Turn the <6> or <5

64You can set various settings with the menus such as the image-recording quality, date/time, etc.* Certain menu tabs and menu items are not displayed

653 Menu Operations1Display the menu screen. Press the <M> button to display the menu screen.2Select a tab. Each time you press the <Q>

3 Menu Operations66Example: When Multi Shot Noise Reduction is setDimmed menu items cannot be set. The menu item is dimmed if another function setting

67If the card is new or was previously formatted by another camera or computer, format the card with this camera.When the card is formatted, all image

Before You Start68 The card is new. The card was formatted by a different camera or a computer. The card is full with images or data. A card-relat

69Before You StartYou can prevent the beeper from sounding when focus is achieved or during self-timer operation.1Select [Beep]. Under the [z1] tab,

7Quick Start Guide6While holding down the center of the Mode Dial, set it to <A> (Scene Intelligent Auto) (p.29).All the necessary camera setti

Before You Start70You can set how long the image is displayed on the LCD monitor just after shooting. To keep the image displayed, set [Hold]. To not

71Before You StartShooting Function SettingsAF SettingsAF operation One-Shot AFCase 1 - 6Case1/Parameter settings of all cases clearedAF area selectio

Before You Start72Image Recording Settings Camera SettingsImage quality 73 Auto power off 1 min.Picture Style Standard Beep EnableAuto Lighting Optimi

73Before You StartLive View Shooting Settings Movie Shooting SettingsLive View shootingEnable Movie Servo AF EnableAF method u+Tracking AF method u+Tr

74You can display a grid in the viewfinder to help you check the camera tilt or compose the shot.1Select [Viewfinder display]. Under the [52] tab, se

75You can display the electronic level on the LCD monitor and in the viewfinder to help you correct camera tilt.1Press the <B> button. Each tim

Q Displaying the Electronic Level76An electronic level can be displayed on the upper part of the viewfinder. Since this can be displayed while you sho

77The shooting function settings (Shooting mode, White balance, Drive mode, AF operation, Metering mode, Image quality: JPEG/RAW, Flicker detection) c

78When [z Help] is displayed at the bottom of the menu screen, the feature’s description (Help) can be displayed. The Help screen is displayed only wh

792Basic ShootingThis chapter explains how to use the Mode Dial’s <A> (Scene Intelligent Auto) mode for easy picture taking.In the <A> mod

8Icons in this Manual<6> : Indicates the Main Dial.<5> : Indicates the Quick Control Dial.<p> : Indicates the AF area selection leve

80<A> is a fully automatic mode. The camera analyzes the scene and sets the optimum settings automatically. It also adjusts focus automatically

81A Fully Automatic Shooting (Scene Intelligent Auto)4Take the picture. Press the shutter button completely to take the picture. The captured image

A Fully Automatic Shooting (Scene Intelligent Auto)82 Pressing the shutter button halfway does not focus on the subject.If the focus mode switch on t

83Depending on the scene, position the subject toward the left or right to create a balanced background and good perspective.In the <A> mode, pr

A Full Auto Techniques (Scene Intelligent Auto)84You can shoot while viewing the image on the LCD monitor. This is called “Live View shooting”. For de

853Setting the AF andDrive ModesThe AF points in the viewfinder are arranged to make AF shooting suitable for a wide variety of subjects and scenes.Yo

86You can select the AF operation characteristics to suit the shooting conditions or subject. In the <A> mode, “AI Focus AF” is set automaticall

87f: Selecting the AF OperationNSuited for still subjects. When you press the shutter button halfway, the camera will focus only once. When focus is

f: Selecting the AF OperationN88This AF operation is suited for moving subjects when the focusing distance keeps changing. While you hold down the shu

89f: Selecting the AF OperationNWhen you press the shutter button halfway and the camera is focusing with AF, the <i> icon will appear on the lo

9For first-time DSLR users, Chapters 1 and 2 explain the camera’s basic operations and shooting procedures.ChaptersIntroduction2Getting Started37Basic

90The camera has 65 AF points for autofocusing. You can select the AF area selection mode and AF point(s) suiting the scene or subject.Depending on th

91S Selecting the AF Area and AF PointNAF point expansion (Manual selection, surrounding points)The manually-selected AF point <S> and the surro

S Selecting the AF Area and AF PointN921Press the <S> button. (9)2Operate the <p> or <B> button. Look through the viewfinder and op

93S Selecting the AF Area and AF PointNYou can manually select the AF point or zone.1Press the <S> button. The AF points will be displayed in t

S Selecting the AF Area and AF PointN94Pressing the <S> button lights up the AF points that are cross-type AF points for high-precision autofocu

95For pinpoint focusing over a narrower area than with single-point AF (manual selection). Select one AF point < > to focus.Effective for pinpoi

AF Area Selection ModesN96The manually-selected AF point <S> and surrounding AF points <w> are used to focus. The AF point expansion is la

97AF Area Selection ModesNThe AF area is divided into three focusing zones (left, center, and right) for focusing. Since the focusing area is larger t

AF Area Selection ModesN98 When AI Servo AF mode is set with 65-point automatic selection AF, Large Zone AF (manual selection of zone), or Zone AF (m

99The camera’s AF sensor has 65 AF points. The illustration below shows the AF sensor pattern corresponding to each AF point. With f/2.8 or larger max